BMS High Flow V2 Intake for 2021+ Mazda 3 & CX30 SKYACTIV® 2.5L Turbo

More Air = More Power + Incredible Sound

Finally, a performance intake system worthy of your 2021+ Mazda 3 and CX-30 2.5L Turbo. The Burger Motorsports intake replaces the entire factory intake system with a higher-flowing design engineered specifically for performance.

The core of the system is our BMS renewable inverted cone air filter capable of supporting 500+ wheel horsepower. The restrictive factory turbo inlet tube is replaced with a high-flow aluminum pipe, and a CNC-machined billet MAF housing ensures precise airflow calculations. An integrated heat shield and mounting bracket secure everything in place for OEM-level fitment and durability. Finished in powder-coated black, this intake is built to last the life of your vehicle.

The BMS intake is offered in two stages:

Stage 1 – Top Mount: Installs in the factory airbox location for the simplest installation and maximum induction sound.

Stage 2 – Fender Mount: Extends the filter into the fender area for true cold air intake performance and lower intake temperatures. No bumper removal is required for installation.

Power gains are up to 15whp peak on factory tuning, with over 30whp gained under the curve in upper RPM ranges. In addition to improved power, turbo response and intake sound are dramatically enhanced. This is how your Mazda should have come from the factory.

We recommend cleaning the filter every 15–20k miles using an S&B cleaning kit.

Features & Benefits

• Up to 15+ whp power gains
• 30+ whp gains under the curve
• Dramatic turbo and induction sound improvement
• Stage 1 upgradeable to Stage 2 at any time
• Improved throttle response
• Outflows factory intake system
• Upper heat shield included
• Renewable high-flow air filter
• Clean OEM+ appearance

Vehicle Fitment

• 2021+ Mazda 3 SKYACTIV® 2.5L Turbo
• 2021+ Mazda CX-30 SKYACTIV® 2.5L Turbo

What’s Included

Stage 1 – Top Mount Intake

• (1) Intake pipe
• (1) Heat shield
• (1) M6x1.0x16mm mounting bolt
• (2) M6 washers
• (1) M6 nut
• (2) M6x1.0x12mm MAF housing bolts
• (2) M4x0.7x14mm MAF screws
• (1) Inverted cone air filter
• (1) Billet MAF housing
• (1) 2.5"–3" silicone reducer
  
• (2) 2.5"–3" clamps

Stage 2 – Fender Mount Intake

• (1) Intake pipe
• (1) Secondary larger intake pipe
• (1) Heat shield
• (1) M6x1.0x16mm mounting bolt
• (1) M6 washer
• (1) M6 nut
• (2) M6x1.0x12mm MAF housing bolts
• (2) M4x0.7x14mm MAF screws
• (1) Inverted cone air filter
• (1) Billet MAF housing
• (1) 2.5"–3" silicone reducer
  
• (2) 2.5"–3" clamps
• (1) 3" silicone coupler
• (2) 3" clamps

Performance air filter cleaning kit available here.
Replacement 1053 blue filters available here.
Replacement 1053 red filters available here. 

Stage 1 Top Mount Shown Below

Stage 2 Fender Mount Shown Below
Note: Bumper removal is not required for installation. Bumper was removed for photography only. Prototype shown in photos was not yet powder-coated black.

2021 Mazda 3 2.5T – 91 Octane – Factory Tuning – BMS Stage 1 vs Factory Intake

2021 Mazda 3 2.5T – 91 Octane – JB4 Map 2 – BMS Stage 1 vs Factory Intake

Mazda 3 Dyno Video (Stock vs BMS Intake)

Intake Sound Clip (Inside Cabin)

Vehicle fitment